Haneda v4 · Walkthrough answers
MH-93 workspace and separate MH-92 sampler references. Dimensions, driving and fuel values are synthetic learning settings, not an approved Haneda procedure. v4: wrong calls (a false report, opening supply unbonded, resuming without clearance) are not refused; their consequences follow. Refreshing starts a new run.
1 / 14
Prepare
Inspect the work order and vehicle condition in the cab.
Verify the order · single
Match registration and flight number; ask the operations supervisor whether the quantity means final fuel onboard or uplift. Do not fuel until clarified.
Match aircraft identity, clarify the basis with the operations supervisor, hold fueling
2 / 14
Brake test
Release the parking brake, move slowly, brake to a stop and report the measured test.
Measured stopping response · performance
Perform the stated physical goal. Answering cannot complete it for you.
3 / 14
Wait & enter
Confirm cone handover and entry clearance separately; approach along a curved path.
Entry decision · single
No. Cone handover and clearance are separate. Verify beacon, chocks and clearance individually.
No — verify the separate entry conditions
4 / 14
Position
Use mirrors and socket reach to park forward inside the marked bay. Correct positioning from a safe location.
Parking & reach · performance
Perform the stated physical goal. Answering cannot complete it for you.
5 / 14
Secure
Apply the parking brake, leave the cab, fit chocks and connect bonding.
Secure before work · multi
Parking brake, chocks and bonding at the designated point. Do not drive with the platform raised.
Parking brake / Vehicle chocks / Bonding at the designated point
6 / 14
Hydrant
Deploy the inlet hose, walk to the pit, align, seat, lock and inspect the coupler.
Coupling operations · order
Deploy → align → seat → lock → inspect. The answer does not perform the connection.
7 / 14
Under the wing
Board the lowered platform, adjust its height, then align, seat, lock and inspect the nozzle.
Verify wing connection · performance
Perform the stated physical goal. Answering cannot complete it for you.
8 / 14
Sample quality
Lower and leave the platform. Prepare the sample branch; collect, inspect visually and test the capsule. Report abnormal results, drain and retest before reporting the new sample.
Two distinct observations · observe
Inspect chamber appearance and water-detector capsule separately. Inspect again after replacing a sample.
Abnormal sample · single
Hold main transfer and report to the supervisor. In this synthetic exercise, carry out authorized recovery, drain, then inspect and report a new sample.
Hold, report and retest after recovery
9 / 14
Start transfer
Check connection and QC conditions; operate the valve and hold the deadman.
Actual simulated transfer · performance
Meet QC and connection conditions, operate valves and hold the deadman to increase the total.
10 / 14
Monitor
Inspect the instruments during transfer. The simulation pauses while answering or reading feedback.
Read the totalizer · numeric
Inspect the instrument and enter totalLitres from that observation. Tolerance ±1 L.
11 / 14
Stop & recover
When the synthetic pressure anomaly occurs, stop and report. Resume only after recovery clearance, finish at the target and close the valves.
Explain stop & recovery · text
Identify the observed pressure anomaly, stop by releasing the deadman and closing valves, report to the operations supervisor, and resume only after cause review and clearance. Do not claim actions you did not perform.
12 / 14
Disconnect
Confirm stopped and depressurized, disconnect and stow the nozzle and inlet. Remove bonding last.
Safe disconnection · order
Confirm transfer is stopped and depressurized, remove the wing nozzle and close the adapter cap and panel door. Then close the pit valve, remove its coupler and secure the cover. Remove bonding last.
13 / 14
Reconcile & hand over
Inspect final meters, reconcile litres and kilograms, report and complete handover.
Final mass · numeric
Use the final totalKg observation. Synthetic density is 0.8 kg/L; 300 L equals 240 kg. Inspect, reconcile and hand over physically too.
14 / 14
Walk around & depart
Complete the walkaround, remove chocks, enter the cab and drive forward to the exit.
Forward departure · performance
Perform the stated physical goal. Answering cannot complete it for you.